Welcome Guest. ( logon | register )   
FAQ Member List Albums Today's Posts Search

PointedThree :  Vans, Trucks, SUVs and Other Forums : W163 M-Class : WIS - Workshop Information System

Page 4 of 4 1234
WIS - Workshop Information System
Topic Tools Message Format
Author
Posted 2/3/2009 1:56 PM
akadi

Date registered: Dec 1899
Location:
Vehicle(s):
RE: WIS - Workshop Information System

Hi,
I am trying to replace the light bulb of the heater control in the center console of a 1999 ML350. When I remove the middle knob of the AC/heater control, I can see the bulb but its housed inside a plastic frame which makes it impossible to reach the bulb.
Any help will be truly appreciated

Thanks,





Edited by akadi 2/3/2009 2:01 PM
#142723 - in reply to #11245
Top of the page Bottom of the page
Author
Posted 4/4/2009 11:52 AM
dave45056
New user


Date registered: Dec 2008
Location:
Vehicle(s):
Posts: 2

Re: WIS - Workshop Information System

Use a piece of tygon tubing. Slip it over the bulb and pull it out. The new bulbs are all glass and are about 4.9mm diameter. The old bulbs have a platic base and are slightly smaller diameter. Tygon is very flexible, so get a tube that is about 4mm or 5/32" id. Hope this helps someone if not the original poster.
#148020 - in reply to #11245
Top of the page Bottom of the page
Author
Posted 6/24/2009 7:30 PM
rb48901
Member


Date registered: Jun 2009
Location: Adelaide Australia
Vehicle(s): ML320 Luxury Pack
Posts: 8

RE: WIS - Workshop Information System

Could you please publish any WI for RHD specific vehicles if there are any? Plus I need to know how to remove the pedals (brake, accelerator) from the bulkheads/firewalls

Thanks

Bob
#152906 - in reply to #11245
Top of the page Bottom of the page
Author
Posted 9/28/2009 11:25 AM
blade

Date registered: Dec 1899
Location:
Vehicle(s):
Re: WIS - Workshop Information System

Help with SRS light is on.
When i have a pasanger in front seat will go out.
Any idea how to replace sensor on the seat???
#157787 - in reply to #11245
Top of the page Bottom of the page
Author
Posted 2/14/2010 7:15 PM
sleinbach

Date registered: Dec 1899
Location:
Vehicle(s):
RE: WIS - Workshop Information System

I was looking for a rotor and brake pad change instructions. Did I miss it?
#166419 - in reply to #11245
Top of the page Bottom of the page
Author
Posted 4/3/2010 9:53 PM
DTP

Date registered: Dec 1899
Location:
Vehicle(s):
RE: WIS - Workshop Information System

Could anyone help with the tail light wiring or instruction of connecting trailer connector. I am installing the hitch and need to connect the trailer electrical hookup. Thank you in advance.
DTP
#169202 - in reply to #11245
Top of the page Bottom of the page
Author
Posted 4/6/2010 2:23 AM
rb48901
Member


Date registered: Jun 2009
Location: Adelaide Australia
Vehicle(s): ML320 Luxury Pack
Posts: 8

RE: WIS - Workshop Information System

dont worry about the throttle pedal removal, just learnt I had to unhook the throttle cable first to give enough movement to lift the pedal of the locating pins. Problem solved. As for rhd information, that's just to exotic for the NA market.
#169288 - in reply to #152906
Top of the page Bottom of the page
Author
Posted 9/15/2010 12:37 PM
riccco
New user


Date registered: Sep 2010
Location:
Vehicle(s):
Posts: 1

Re: WIS - Workshop Information System

Hi,

I have a MB ML430 AMG year 2001

I hava problem with my Automatic trasmission, sometimes it doesent change gear (stuck in 2-gear)

I get the faultcode:
RPM sensor in Aut. transmission fault
On my code reader.

I know its the sensor in the Automatic transmission thats the problem beacuse i reset the codes and the tranny works for a couple of days.
And probably its only requires a oli and filter change and a cleaning of the sensor.
But i need to get my hand on a PDF-file with DIY information about the tranny (were the sensor is located etc.)
Can anyone help me?
Please!

The MB-shop wants 650$ for the job, money i dont have....
#177488 - in reply to #11245
Top of the page Bottom of the page
Author
Posted 10/19/2011 6:07 PM
Lisel
New user


Date registered: Oct 2011
Location:
Vehicle(s):
Posts: 2

Re: WIS - Workshop Information System

here you have everything

http://www.benzworld.org/forums/w163-m-class/1257818-automatic-tran...



(inductive speed sensor.jpg)



Attachments
----------------
Attachments inductive speed sensor.jpg (45KB - 95 downloads)
Attachments Lambda Sensor.pdf (86KB - 71 downloads)
#195938 - in reply to #177488
Top of the page Bottom of the page
Author
Posted 2/23/2012 10:00 PM
jpose72
New user


Date registered: Feb 2012
Location:
Vehicle(s): 2000 ML320
Posts: 4

Re: WIS - Workshop Information System

Im looking for help in replacing the light bulb under the center console controls.
Any ideas?? 2000ml320
#200898 - in reply to #11245
Top of the page Bottom of the page
Author
Posted 1/26/2013 12:00 PM
wembley
New user


Date registered: Jan 2013
Location:
Vehicle(s):
Posts: 1

Re: WIS - Workshop Information System

does anyone has a clue to change left or right front fender?
#210689 - in reply to #11245
Top of the page Bottom of the page
Author
Posted 1/29/2013 3:30 PM
mickey.1214
Member


Date registered: Aug 2008
Location:
Vehicle(s):
Posts: 6

Re: WIS - Workshop Information System

Wembly: If you don't get any response, you can pay $18US for a 24 hour subscription to StarTek:
http://www.startekinfo.com/StarTek/
#210807 - in reply to #11245
Top of the page Bottom of the page
Author
Posted 6/5/2013 2:57 PM
ianstaley
Member


Date registered: Feb 2013
Location: Pontefract
Vehicle(s): ML 270CDi, W202, Camry and Toyota Supra MK3
Posts: 7

Re: WIS - Workshop Information System

I have looked down the list of PDF's but haven't found one on retrofitting the spare wheel carrier. So the real question is "is there one" I have found a few on retro fitting the bush bar's front that is going to be helpful but nothing of that damned rear spare wheel carrier.

If someone has such a document I would really like to have a copy.. Ian PLEASE...Pretty PLEASE
#214505 - in reply to #11245
Top of the page Bottom of the page
Author
Posted 7/31/2013 8:53 PM
jboyd
New user


Date registered: Jul 2013
Location:
Vehicle(s):
Posts: 1

Re: WIS - Workshop Information System

Need help getting rear cup holder removed. Removed lid and 2 screws in track. I can see the 2 flanges on top that can be pushed up, but still very tight. Thanks 2003 350ml
#216065 - in reply to #11245
Top of the page Bottom of the page
Author
Posted 9/12/2014 3:19 PM
dentosan
New user


Date registered: Feb 2014
Location: Cirencester, England
Vehicle(s): ML270
Posts: 2

RE: WIS - Workshop Information System

Hi Pleubner, rear shock replacement for W163 please. Many thanks for all you hard work, much appreciated.
#223963 - in reply to #11245
Top of the page Bottom of the page
Author
Posted 9/13/2014 7:35 AM
DUTCH
Administrator Doppelgänger




Date registered: Apr 2006
Location: US, GA, Atlanta
Vehicle(s): 2000 G500 NMLE, 2015 Audi Q7 3.0 TDI
Posts: 9398
5000
RE: WIS - Workshop Information System

dentosan - 9/12/2014 3:19 PM

Hi Pleubner, rear shock replacement for W163 please. Many thanks for all you hard work, much appreciated.


Pleubner hasn't contributed on this forum in over 8 years.
#223971 - in reply to #223963
Top of the page Bottom of the page
Author
Posted 9/16/2015 6:53 PM
sufi420
New user


Date registered: Sep 2015
Location:
Vehicle(s):
Posts: 1

Re: WIS - Workshop Information System

Hi.. thanks to the uploader of making a hard job easy... again thanks
#229515 - in reply to #11245
Top of the page Bottom of the page
Author
Posted 2/23/2017 9:37 AM
DMW54
New user


Date registered: Apr 2016
Location:
Vehicle(s):
Posts: 1

Re: WIS - Workshop Information System

Re: WIS Workshop Information System

Looking for wiring diagram for Command 2 and for the Zenon Headlights
#235411 - in reply to #11245
Top of the page Bottom of the page
« View previous thread :: View next thread »
Page 4 of 4 1234
Forum Jump :
All times are EST.  The time is now 6:30:46 AM.

Execution: 0.484 seconds, 92 cached, 22 executed.