|
akadi
Date registered: Dec 1899
Location:
Vehicle(s):
| RE: WIS - Workshop Information System
Hi,
I am trying to replace the light bulb of the heater control in the center console of a 1999 ML350. When I remove the middle knob of the AC/heater control, I can see the bulb but its housed inside a plastic frame which makes it impossible to reach the bulb.
Any help will be truly appreciated
Thanks,
Edited by akadi 2/3/2009 2:01 PM
|
|
| |
|
dave45056
New user
Date registered: Dec 2008
Location:
Vehicle(s):
Posts: 2
| Re: WIS - Workshop Information System
Use a piece of tygon tubing. Slip it over the bulb and pull it out. The new bulbs are all glass and are about 4.9mm diameter. The old bulbs have a platic base and are slightly smaller diameter. Tygon is very flexible, so get a tube that is about 4mm or 5/32" id. Hope this helps someone if not the original poster. |
|
| |
|
rb48901
Member
Date registered: Jun 2009
Location: Adelaide Australia
Vehicle(s): ML320 Luxury Pack
Posts: 8
| RE: WIS - Workshop Information System
Could you please publish any WI for RHD specific vehicles if there are any? Plus I need to know how to remove the pedals (brake, accelerator) from the bulkheads/firewalls
Thanks
Bob
|
|
| |
|
blade
Date registered: Dec 1899
Location:
Vehicle(s):
| Re: WIS - Workshop Information System
Help with SRS light is on.
When i have a pasanger in front seat will go out.
Any idea how to replace sensor on the seat??? |
|
| |
|
sleinbach
Date registered: Dec 1899
Location:
Vehicle(s):
| RE: WIS - Workshop Information System
I was looking for a rotor and brake pad change instructions. Did I miss it? |
|
| |
|
DTP
Date registered: Dec 1899
Location:
Vehicle(s):
| RE: WIS - Workshop Information System
Could anyone help with the tail light wiring or instruction of connecting trailer connector. I am installing the hitch and need to connect the trailer electrical hookup. Thank you in advance.
DTP |
|
| |
|
rb48901
Member
Date registered: Jun 2009
Location: Adelaide Australia
Vehicle(s): ML320 Luxury Pack
Posts: 8
| RE: WIS - Workshop Information System
dont worry about the throttle pedal removal, just learnt I had to unhook the throttle cable first to give enough movement to lift the pedal of the locating pins. Problem solved. As for rhd information, that's just to exotic for the NA market.
|
|
| |
|
riccco
New user
Date registered: Sep 2010
Location:
Vehicle(s):
Posts: 1
| Re: WIS - Workshop Information System
Hi,
I have a MB ML430 AMG year 2001
I hava problem with my Automatic trasmission, sometimes it doesent change gear (stuck in 2-gear)
I get the faultcode:
RPM sensor in Aut. transmission fault
On my code reader.
I know its the sensor in the Automatic transmission thats the problem beacuse i reset the codes and the tranny works for a couple of days.
And probably its only requires a oli and filter change and a cleaning of the sensor.
But i need to get my hand on a PDF-file with DIY information about the tranny (were the sensor is located etc.)
Can anyone help me?
Please!
The MB-shop wants 650$ for the job, money i dont have....
|
|
| |
|
Lisel
New user
Date registered: Oct 2011
Location:
Vehicle(s):
Posts: 2
| Re: WIS - Workshop Information System
here you have everything
http://www.benzworld.org/forums/w163-m-class/1257818-automatic-tran...
 (inductive speed sensor.jpg)
Attachments
----------------
 inductive speed sensor.jpg (45KB - 135 downloads)
Lambda Sensor.pdf (86KB - 109 downloads)
|
|
| |
|
jpose72
New user
Date registered: Feb 2012
Location:
Vehicle(s): 2000 ML320
Posts: 4
| Re: WIS - Workshop Information System
Im looking for help in replacing the light bulb under the center console controls.
Any ideas?? 2000ml320 |
|
| |
|
wembley
New user
Date registered: Jan 2013
Location:
Vehicle(s):
Posts: 1
| Re: WIS - Workshop Information System
does anyone has a clue to change left or right front fender? |
|
| |
|
mickey.1214
Member
Date registered: Aug 2008
Location:
Vehicle(s):
Posts: 6
| Re: WIS - Workshop Information System
Wembly: If you don't get any response, you can pay $18US for a 24 hour subscription to StarTek:
http://www.startekinfo.com/StarTek/ |
|
| |
|
ianstaley
Member
Date registered: Feb 2013
Location: Pontefract
Vehicle(s): ML 270CDi, W202, Camry and Toyota Supra MK3
Posts: 7
| Re: WIS - Workshop Information System
I have looked down the list of PDF's but haven't found one on retrofitting the spare wheel carrier. So the real question is "is there one" I have found a few on retro fitting the bush bar's front that is going to be helpful but nothing of that damned rear spare wheel carrier.
If someone has such a document I would really like to have a copy.. Ian PLEASE...Pretty PLEASE |
|
| |
|
jboyd
New user
Date registered: Jul 2013
Location:
Vehicle(s):
Posts: 1
| Re: WIS - Workshop Information System
Need help getting rear cup holder removed. Removed lid and 2 screws in track. I can see the 2 flanges on top that can be pushed up, but still very tight. Thanks 2003 350ml |
|
| |
|
dentosan
New user
Date registered: Feb 2014
Location: Cirencester, England
Vehicle(s): ML270
Posts: 2
| RE: WIS - Workshop Information System
Hi Pleubner, rear shock replacement for W163 please. Many thanks for all you hard work, much appreciated. |
|
| |
|
DUTCH
Administrator Doppelgänger
Date registered: Apr 2006
Location: US, GA, Atlanta
Vehicle(s): 2015 Audi Q7 3.0 TDI,2018 Sprinter
Posts: 9963
| RE: WIS - Workshop Information System
dentosan - 9/12/2014 3:19 PM
Hi Pleubner, rear shock replacement for W163 please. Many thanks for all you hard work, much appreciated.
Pleubner hasn't contributed on this forum in over 8 years. |
|
| |
|
sufi420
New user
Date registered: Sep 2015
Location:
Vehicle(s):
Posts: 1
| Re: WIS - Workshop Information System
Hi.. thanks to the uploader of making a hard job easy... again thanks |
|
| |
|
DMW54
New user
Date registered: Apr 2016
Location:
Vehicle(s):
Posts: 1
| Re: WIS - Workshop Information System
Re: WIS Workshop Information System
Looking for wiring diagram for Command 2 and for the Zenon Headlights |
|
| |
|
Mijova
New user
Date registered: Aug 2017
Location:
Vehicle(s):
Posts: 3
| Re: WIS - Workshop Information System
wind shied washing system M350) 2004 change a pump any manual |
|
| |
|
Mijova
New user
Date registered: Aug 2017
Location:
Vehicle(s):
Posts: 3
| Re: WIS - Workshop Information System
Any one has this PDF ( for ML350 ( 2004)
Overhead control Panel - popup,sliding roof - remove&install.pdf
simply cannot be load
Regards Mijova |
|
| |
